A-A-50455A
2.17.2 Sufficient space and clearances shall be provided for common maintenance procedures, such as filter change- out and fluid sampling, with minimal effort and without breaking pipelines. Location of sampling valves and unit ports shall minimize damage to these valves during transit of cart and provide access for fluid sample containers.
3. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).
4. PRODUCT CONFORMANCE. The products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producer's own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance.
5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
6. NOTES.
6.1 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and PIN. b. Product conformance provisions.
c. Flow rate required (see 2.4).
d. Electrical power required (see 2.3.2).
e. Warning plate for use in Class I, Division 1, hazardous spaces is optional (see 2.13.3.2).
6.2 Part or identification number. The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. The part number consists of the basic number of this commercial item description plus applicable flow rate and power requirement numbers selected from Table I.
EXAMPLE: AA50455-10-115 is a filtration cart with 10 gpm (37.8 lpm) flow rate, 115 volts power.
6.3 Acceptable units. The brand names and manufacturer's part numbers of filtration carts which are known to be acceptable and of current manufacture are available from: Commander, Naval Sea Systems Command, Attn: SEA
05Z6, 1333 Isaac Hull Ave SE Stop 5125, Washington Navy Yard, DC 20376-5125. Manufacturers desiring listing
of their products should submit drawings and test data that demonstrate compliance with this specification.
6.4 Sourc e of documents.
6.4.1 ASME. ASME standards are available from American Society of Mechanical Engineers, 22 Law Drive, Box
2300, Fairfield, NJ 07007-2300 or online at https://www.asme.org.
6.4.2 ASTM. ASTM standards are available from ASTM International, 100 Barr Harbor Dr., West Conshohocken, PA 19428, or online at www.astm.org.
6.4.3 FAR. The Federal Acquisition Regulation may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402 or online at https://www.arnet.gov/far.
6.4.4 IEEE. IEEE standards are available from Institute of Electrical and Electronic Engineers, Inc., 445 Hoes
Lane, P.O. Box 1331, Piscataway, NJ 08855-1331 or online at https://standards.ieee.org/.
6.4.5 ISO. ISO standards are available from International Organization for Standardization (ISO), 1, rue de
Varembe, Case postale 56 CH-1211 Geneva 20, Switzerland or online at https://www.iso.org.
6.4.6 M IL- SPECs . Military specifications are available online at https://assist.daps.dla.mil/quicksearch/ or https://assist.daps.dla.mil) or from the Standardization Document Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094.)
6.4.7 NEMA. NEMA standards are available from National Electrical Manufacturers Association, 1300 North 17th
Street, Suite 1847, Rosslyn, VA 22209, or online at www.nema.org.
6
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business